Instructions for the PA-5000®
Assembly: Attach the leather guide thru your existing PA ring. Drop it thru the cage portion and guide the penis thru while holding onto the cage. Make sure the head of the penis clears the end of the cage. Smooth any loose skin at the bottom of the penis back towards the body.
Remove your PA ring and replace it with one of the hooks provided with the package. Line up the hook with the locking slot in the cage.
Push key into the cam lock and gently turn to lock in place.
Cage extender: One cage extender is enclosed for extending the length of the cage if necessary. It is recommended that you use 2 pieces of 1/2” long waterproof tape on each side to hold the extender in place and wear it for one week. If you want to permanently use the extender, put a drop of superglue on each side and allow it to completely dry prior to wearing.
Cleaning/Hygiene: Lather head and shaft of penis with a natural soap. Using the right thumb slide the head of the penis forward and up inserting the small finger on the left hand in order to clean around the piercing pin and inside of the cage. Repeat the steps with the left thumb and right small finger to clean the right side. Rinse thoroughly with water. Hold the penis head and back of cage at the same time. Allow the water to freely run thru the cage removing all soap residue.
Instructions for CB-3000®, THE CURVE® & CB-6000®
Lubricate the head and shaft of the penis using System JO Premium Silicone Lubricant. Put the product on while in a relaxed state.
U-Rings: Put the U-Ring under and behind the testicles and penis. Your kit comes with 5 different sized U-Rings. Choose the size that provides a snug, but not tight fit. We also offer 2 extra large sized U-Rings available for purchase separately.
BASE #1 & #2: Insert the Base # 1 with the guide pins facing out, away from the body through the holes in the U-Ring. Slide the Base # 2 piece onto the guide pins forming a solid ring. Make sure to push the penis in a down position while attaching Base # 1 & Base # 2.
LOCKING PIN: Insert the locking pin through the center holes in Base # 1 & Base # 2.
SPACERS: The spacers are designed in such a way that each spacer fits a particular locking pin.
Your kit comes with either 3 (CB-3000 & The Curve) or 4 (CB-6000s & CB-6000) locking pin and spacer combinations. Choose the one that provides a snug, but not tight fit.
CAGE: Insert the penis into the cage. Push the penis down in order to avoid pinching when connecting the cage to the ring.
PADLOCK: After assembling the ring, guide pins, locking pin and spacers to the cage, attach the brass padlock. Make sure to have a diligent Keyholder!
CLEANING PRODUCT: Use System JO Toy Cleaner and a soft brush to clean. Do NOT use household cleaning products.
NOTE: Always take the time to smooth any loose skin around the rings and cage for the most comfortable fit.
Tight cage? Try the Stocking Trick™: Some customers have success fitting into a tight cage by using something called the stocking trick. You cut the foot out of a nylon stocking and insert the open end through the tip of the CB-6000 slot. Pull most of the stocking through the slot. Insert penis into stocking. Gently push CB-6000 tube onto penis. Slowly slide stocking off by pulling it back out through the slot in reverse. That should pull the penis down into the tube with no discomfort and it should get you all the way down in there without the painful bunching of skin. Using the silicone lubricant that came with your package may help with this.
Your male chastity device is covered by a one year parts replacement warranty. Should any part of your device fail up to one year from purchase please contact us at warranty@CB-X.com for further instructions on receiving a replacement part. Proof of purchase is required so please keep your receipt. If you do not have proof of purchase we cannot cover warranty replacement.
To view our YouTube instructions video, Click Here